20 of the module: It works with motorized roller blinds, venetian blinds, awnings and gates.

You have to register in order to view all content and post in our community. If parameter 40 enables scenes for triple S1 click, disable it or use B-button instead to remove the device.

So first I must pair module with Z-stick then I must change settings to 1 to operate normal with switch. The device is equipped with power and energy monitoring. FIBARO Roller Shutter 3 is a new version of the radio-controller based on Z-Wave 5 technology.

Each one gives the same results and you may choose which one to …

There is a separate procedures to calibrate blinds with lamellas (venetian blind). It went straight up, so I gave up, really disapointed with product. Also afaik this device requires you to securely pair in order to have full capability of the product. This parameter determines to which alarm frames and how the device should react. I installed that one.

It works with 2 shutters but the last one is giving me problems and I don't know why. After 3 hours trying to calibrate it and getting it working, again no succes. I have roller shuter 3 and HC 2. Today received the roller-shutter-2. This parameter determines the minimum change in consumed power that will result in sending new power report to the main controller.This parameter determines in what time intervals the periodic power reports are sent to the main controller.

The shutter-3 is (for me) totally unclear how to set.

De module maakt bediening van huishoudelijke apparaten zoals elektrische jaloezieën, luifels, rolluiken, rolgordijnen, hekken en poorten mogelijk.

Attached some screenshots showing a couple of parameters of the shutter-2 and shutter-3. I bought FIbaro roller shutter 3 on Friday I am really disapponted because this is really garbage of product sorry Fibaro. No solution till now. I have Fibaro roller shutter-2 (FGR-222) working perfectly with Dooya-DT52S curtain motor using a double momentary switches. I have raspbeery pi 3b+ and Aeotec Z-stick as hub for my z-wave devices. By setting this parameter to 2 the device enters the calibration mode. I installed fibaro roller shutter 3 based on manual and after installation I try to include roller shutter to z-stick no response.

Therefore I asked them to sent me a new roller-shutter-3. I wanted to stop it in half way down and no response it continued to full way down. Hello i have 6 of them I have one to the roller shutter and I can’t use my momentary switch  I bought FIbaro roller shutter 3 on Friday I am really disapponted because this is really garbage of product sorry Fibaro.

It went straight up, so I gave up, really disapointed with product. Received the new roller-shutter-3 yesterday and immediately installed it to my HCL and curtain motor. This parameter determines to which alarm frames and how the device should react.

Inclusion was succesfull and yes the parameters where visible on the advanced-tab.

I bought FIbaro roller shutter 3 on Friday I am really disapponted because this is really garbage of product sorry Fibaro. Calibration is mandatory in order for the device to correctly recognize a roller blind position. Installation and calibration was literally a 5 minutes job.

For Venetian blinds (parameter 151 set to 2) the parameter determines time of full turn cycle of the slats.For Venetian blinds (parameter 151 set to 2) the parameter determines slats positioning in various situations.For blinds (parameter 151 set to 1, 2, 5 or 6) the parameter determines the time after which the motor will be stopped after end switch contacts are closed.Power threshold to be interpreted as reaching a limit switch. You can post now and register later. Ok so I am currenty in buying process of Fibaro roller shutter 3 and I will be using on other z-wave hub than HC....is it now OK with firmware or should I also look for roller shutter 2.....probably you can not get update for firmware if you use other z-wave hub

), but not in a way it should be. So first I must pair module with Z-stick then I must change settings to 1 to operate normal with switch. Tried this multiple times. I have ordinary up/down switch - toggle switch as you can see in the uploaded image.

Periodic reports do not depend on energy change (parameter 65). I have raspbeery pi 3b+ and Aeotec Z-stick as hub for my z-wave devices.